M2 AC SERVO MOTOR DRIVES ◊ 50-200 WATTS
 |
 |
|
| Certification | RoHS, CE IEC 61800-3: 2004, IEC 61800-5-1: 2007 | |
| Features: | - Easy to use On-line Auto Tuning | |
| - Advanced Anti Vibration Function | ||
| - Intelligent Q-Programming | ||
| - Various Industrial Field Bus Supported | ||
| - Flexible Internal Position Table | ||
| - Good Response Frequency and Settling Time | ||
| - Various I/O's | ||
| - Easy to use Control Panel | ||
| - Friendly Tuning Software | ||
| - Safety Function STO | ||
FIELD BUS TYPE / ITEM
|
CONTROL MODE
|
50 W
|
100 W
|
200 W
|
| -/- |
Basic Type
|
M2DV-1D82S | M2DV-1D82S | M2DV-1D82S |
| RS-232 |
Q Type
|
M2DV-1D82Q | M2DV-1D82Q | M2DV-1D82Q |
| RS-485 |
SCL
|
M2DV-1D82R | M2DV-1D82R | M2DV-1D82R |
|
Modbus RTU
|
||||
| CAN |
CANopen
|
M2DV-1D82C | M2DV-1D82C | M2DV-1D82C |
| EtherNet / IP |
EtherNet
|
M2DV-1D82IP | M2DV-1D82IP | M2DV-1D82IP |
| eSCL | M2DV-1D82E | M2DV-1D82E | M2DV-1D82E | |
| RATED CURRENT |
[A]
|
1.8 | ||
| MAXIMUM CURRENT |
[A]
|
5.4 | ||
| INPUT POWER |
AC Input
|
Single Phase 240VAC ±10% 50/60Hz | ||
| CONTROL SIGNAL (Digital I/O) |
INPUT
|
8 Configurable Optically Isolated Digital General Inputs (5-24VDC, max input current 20mA) |
||
| 4 Configurable Optically Isolated Digital High Speed Inputs (5-24VDC, max input current 20mA) |
||||
|
OUTPUT
|
5 Configurable Optically Isolated Digital Outputs, 30VDC, max current 30mA One Motor Brake Control Output, 30VDC, max. current 100mA |
|||
| ANALOG SIGNAL |
INPUT
|
2 Analog Inputs, -10VDC ~ +10VDC | ||
|
OUTPUT
|
N/A | |||
| PULSE SIGNAL |
INPUT
|
2 Optically Isolated Inputs 500Khz (Open collector) 2 High Speed Differential Input 2MHz |
||
|
OUTPUT
|
10000 counts/rev, A/B/Z Line Driver | |||
| COMMUNICATION PORT |
USB
|
Online Auto-Tuning | ||
| OPERATION PANEL | 5 Digit, 7 Segment LED Display, 4 Setting Switch | |||
| REGENERATIVE RESISTOR | Build-In | |||
| FAULTS & WARNING | Over-Voltage, Under-Voltage, Over-Current, Encoder Feedback Loss, Drive Over Temperature, Position Error, Safety Function STO |
|||
| ENVIRONMENT | Ambient Temperature: 0~40°C, Humidity: 10~85%, Altitude: <1000m, Vibration: 0.5g | |||
| DOWNLOAD CATALOGUE M2 AC SERVO DRIVES AC Servo Motor Drives M2 Catalogue |
| DIMENSIONS M2DV-1D82 [mm] |
 |
| FEATURE - Easy to Use On-line Auto Tuning |
| M2 servo system can accomplish real time response to the dynamic feedback of the load and optimize gain tuning parameters on-line automatically. This auto tuning function can greatly save debugging time and simplify the debugging procedure. These all can be done by the PC based software in only a few minutes. |
 |
| FEATURE - Intelligent Q programming, Various Industrial Field Bus Supported |
 |
 |
| FEATURE - Flexible Internal Position Table |
| Position Table include Linear motion and Circular motion. Each Position can be triggered by the external digital inputs without the pulse & direction signals send by the motion controllers. ● Up to 64 points in Linear motion. Velocity, acceleration, deceleration can be set separately for each point. ● Up to 12 homing methods for Linear motion. ● Up to 24 division ratios. Indexing Plate can be applied by setting the reduction gear ratio and division ratio. |
 |
| FEATURE - Good Response Frequency and Settling Time |
| M2 has 2.0KHz response frequency and 0-2ms settling time. These come from the high sample rate control algorithm, fast response velocity feed forward and torque feed forward math model and flexible filter function. These greatly shorten the system response time, improve the accuracy and efficiency. |
 |
| FEATURE - Advanced Anti Vibration Function |
| M2 servo system has advanced anti vibration function which include anti resonance and vibration damping. Anti resonance uses two notch filters to overcome the resonance from the natural mechanical characteristic of the system. |
 |
| Vibration damping uses an adjustable damping ratio in the controller to improve the damping characteristic of the system, which can reduce the vibration of the system. |
 |
| FEATURE - Easy to Use Control Panel, Friendly Tuning Software |
On board Control Panel ● Basic parameters setting and query● Drive status LED display M Servo Suite tuning software ● Friendly interface ● Easy set up within just several steps ● Drive set up and configuration ● Easy to use on line auto tuning ● Built in oscilloscope for motion testing and monitoring ● Write and save SCL scripts ● On-line help integrated |
 |
| FEATURE - Various I/Os |
| ● Two EIA-422 standard high speed differential inputs ● Four high speed inputs, accept 5-24VDC, input frequency up to 2MHz with digital filters ● Eight general purpose inputs, 5-24VDC ● Two analog inputs ● Five general purpose outputs, 30VDC 30mA max ● One motor brake control output, 30VDC 100mA max ● Integrated Internal Regeneration Absorbing Resistor, up to 40 Watts |